How to Use Silt Fence
A plain guide to silt fence: digging the trench, setting stakes, placing the fabric on slope and drainage, and keeping sediment out of prairie waterways.
Contents
- What a Silt Fence Does and Does Not Do
- Planning the Line Before You Dig
- Silt Fence Installation Steps
- Stake Spacing and Fabric Tension
- Managing Water and Sediment Behind the Fence
- Where Silt Fence Belongs and Where It Fails
- Inspecting and Retiring the Fence
- Silt Fence Questions for Prairie Sites
- How deep should the silt fence trench be?
- How far apart should silt fence stakes be?
- Can silt fence go on a slope?
- How often should trapped sediment be removed?
- Does silt fence work in a drainage ditch?
- When should silt fence be removed?
Silt fence is a temporary sediment barrier made of geotextile fabric stretched across stakes and buried in the ground. You use it by trenching along the line, setting the fabric in the trench, backfilling and compacting the soil, then staking the fabric upright so muddy runoff ponds and drops its sediment. The fence works only when the fabric is buried, the stakes hold it tight, and the line follows the contour of the slope.
- Silt fence stops sheet runoff and lets sediment settle; it does not divert a channel or replace a ditch.
- Bury the fabric in a trench with compacted soil so water cannot slip under the bottom edge.
- Run the fence along the contour, on the downhill side of disturbed ground, so ponded water spreads and slows.
- Space stakes close enough to keep the fabric from sagging under the weight of water and mud.
- Inspect after every storm and remove trapped sediment before it fills the fabric height.
What a Silt Fence Does and Does Not Do
A silt fence is a sediment barrier that slows sheet runoff and filters soil out of the water before it reaches a prairie stream, wetland or roadside ditch. The fabric lets water seep through while the soil particles settle behind it as ponded water. This makes silt fence a perimeter control for disturbed ground, not a tool for moving water from one place to another.
Silt fence is not a substitute for a diversion berm, a rock check dam or a storm drain inlet filter. A fence placed in a concentrated flow path will be pushed over or undermined by the current. Where water gathers in a channel, a trained erosion control specialist should design the structure instead. The same applies on steep or long slopes, where the fence alone cannot hold the runoff.
Prairie soils that freeze and thaw, or that turn to deep mud after rain, stress a silt fence more than dry ground does. Fabric that is not buried and compacted can lift out of the trench in a freeze. A fence installed on a prairie site should be checked after the first heavy rain and kept clear of tall grass and debris that hide damage.
Planning the Line Before You Dig
Sediment barrier placement starts with a walk along the downhill edge of the area you will disturb. The line should sit on the contour, so the ground under the fence is level along its length, and the fence should face the runoff. Placing silt fence on the contour lets water pond evenly and drop sediment instead of running along the fabric and eroding the soil under it.
Slope and drainage placement decide whether a silt fence can work at all. Keep the fence off the floor of a swale or drainage channel where water concentrates, and keep it back from the toe of a steep slope. On a long slope, a single fence at the bottom may be too little; the plan may need several short runs or a different control altogether. Only a qualified designer should approve a fence on unstable ground.
Mark the line with flags before digging and check it from above, because the contour is easier to see from a distance. Leave a level, undisturbed strip between the disturbed area and the fence so soil does not spill over the top. Locate the fence where a machine can reach it for trenching and where sediment can later be dug out without damaging the fabric.
Silt Fence Installation Steps
Silt fence installation steps begin with a narrow trench dug along the marked line, deep enough that the bottom edge of the fabric sits below the ground surface. Cut the trench through the topsoil and into firm soil so the backfill will knit together. A flat spade or a trencher works for short runs, while a machine-mounted trencher suits long perimeters.
Unroll the fabric along the trench with the staked side facing the runoff, then set it into the trench so the bottom rests on the trench floor. Push the fabric down with a blunt tool and keep it taut along the line. The top of the fabric should stay at a consistent height so ponded water spreads across the whole run rather than spilling at one low spot.
Trench and backfill come together as one job: shovel soil back into the trench against the fabric in layers, then compact each layer by foot or with a hand tamper. Loose backfill lets water tunnel under the fabric and wash out the trench. Drive stakes on the downhill side of the fabric, against it, so the load of water pushes the fabric into the stakes rather than pulling them out.
- Mark the contour line with flags and clear tall grass from the strip.
- Dig a narrow trench along the line and cut into firm soil.
- Unroll the fabric and set the bottom edge on the trench floor.
- Backfill the trench in layers and compact each layer.
- Drive stakes against the downhill face of the fabric.
- Fasten the fabric to each stake and pull the run tight.
Stake Spacing and Fabric Tension
Stake spacing is set by the load the fabric must carry, so a fence on a long or steep drainage area needs stakes closer together. Stakes hold the fabric upright while ponded water presses on it, and wide spacing lets the fabric sag and spill muddy water over the top. Wood stakes of a stout size, or steel posts, suit this job; flimsy garden stakes bend under a full pond.
Fabric tension matters as much as spacing, because slack fabric catches the water and pulls on fewer stakes. Pull the run tight from stake to stake and fasten the fabric at each one with staples or ties so the load spreads along the line. Add a stake wherever the fabric changes direction or the ground drops, since those points take extra strain.
Stake depth depends on the soil: firm prairie ground holds a shorter stake than soft, saturated ground does. Drive each stake below the trench bottom where the soil is loose, and check it for wobble before the fence takes any water. A stake that moves by hand will move further when the runoff arrives.
Managing Water and Sediment Behind the Fence
Water ponds behind a silt fence and drops sediment, so the trapped soil builds up along the fabric and must be removed. Maintenance and sediment removal keep the barrier working: scoop out the pile when it reaches partway up the fabric, before runoff can carry it over the top. Spread the removed soil in a stable spot away from the fence and away from any waterway.
A fence loaded with sediment holds less water for the next storm and can fail at the point where soil touches the fabric top. Remove trapped sediment with a shovel or a small machine, working from the ends toward the middle so the fabric is not torn. Replace any fabric that is ripped, sagging or pulled from the trench, and reset stakes that lean.
Keep grass and trash clear of the fence face so water can pass through the fabric and the structure can be seen. On a prairie site, tall vegetation can hide a collapsed trench until the next rain washes soil through the gap. After each storm, walk the full length and look for washouts at the ends, under the fabric and around each stake.
Where Silt Fence Belongs and Where It Fails
Silt fence suits the downhill edge of a disturbed area where runoff leaves as thin sheet flow and where the ground is stable enough to hold stakes. A garden bed, a utility repair, a trail edge or a small building pad on a prairie site can use a perimeter fence as a temporary barrier. The fence belongs between the bare soil and whatever water body or ditch the runoff would reach.
A silt fence fails when water flows in a channel, when the fence sits on a steep slope without support, or when the trench is shallow and loose. Fabric that is stretched across a gully will be undercut by the current no matter how many stakes it has. Rock or a hard structure, designed by a trained specialist, is the right control where flow concentrates.
By the same token, a fence on frozen or snow-covered ground cannot be trenched, so installation waits for thawed soil. A fence left in place after the ground is stabilized and vegetated becomes a trap for debris and a barrier to wildlife. Remove it when the work is done and the soil is held by plants.
Inspecting and Retiring the Fence
A silt fence needs a check after every significant rain and at regular intervals while the ground is bare. Look for fabric pulled out of the trench, stakes leaning, soil piled past partway up the fabric and water cutting around the ends. Each of these signs means sediment is escaping, so fix the fence before the next storm.
Retiring the fence means pulling stakes, lifting the fabric and filling the trench with compacted soil. Fold and roll the fabric for reuse if it is sound, or dispose of torn material properly. Remove trapped sediment and spread it where it will not wash back into the drainage.
Record where the fence stood and what failed, because a prairie site with freeze and thaw cycles may need a different layout next season. A trained erosion control specialist should review any fence that failed badly before a new one goes in the same place.
Silt Fence Questions for Prairie Sites
How deep should the silt fence trench be?
The trench should be deep enough that the bottom edge of the fabric sits below the ground surface and can be covered by compacted soil. Depth depends on the soil and the fabric height, so check the material instructions and cut into firm soil rather than just topsoil. A shallow trench lets water tunnel under the fence.
How far apart should silt fence stakes be?
Stake spacing depends on the water load and the ground, with closer stakes needed where runoff gathers or the slope is steeper. Follow the spacing given for the fabric you use and add stakes at corners and low spots. Stakes set too wide apart let the fabric sag and spill muddy water.
Can silt fence go on a slope?
Silt fence can sit on a slope only when it is placed along the contour and the ground holds stakes, and a steep or long slope may need a different control designed by a specialist. A fence running straight down a slope will concentrate water and fail. Check the layout with a qualified designer before digging.
How often should trapped sediment be removed?
Sediment should come out when the pile reaches partway up the fabric, and the fence should be checked after each storm. Removing it early keeps room for the next runoff and protects the fabric from tearing. Spread the soil where it cannot wash back into the drainage.
Does silt fence work in a drainage ditch?
No, silt fence is a sheet-flow barrier and does not hold in a concentrated channel where the current pushes it over or undercuts the trench. Rock check dams or other hard structures, designed by a trained specialist, suit a ditch. Keep silt fence on the contour at the edge of disturbed ground.
When should silt fence be removed?
Silt fence should come out once the disturbed ground is stabilized and held by vegetation or another cover. A fence left standing traps debris and blocks wildlife movement, and its trench can hold water. Pull the stakes, lift the fabric and compact soil back into the trench.