PRAIRIE FIELD NOTES / MONTANA

How to Mow Tall Grass with an Electric Mower

Learn to cut tall grass with an electric or cordless mower: raise the deck, mow in passes, stretch battery runtime and clear clogs safely.

10 min read10 viewsHow to Mow Tall Grass with an Electric Mower
— · 0 votes
Contents
  1. Why tall grass strains an electric mower
  2. Walking the area before you start mowing
  3. Setting the deck height for the first cut
  4. Cutting tall grass in passes, step by step
  5. Stretching battery runtime on a cordless mower
  6. Using a corded electric mower in tall grass
  7. Clearing clogs and damaged blades safely
  8. Timing the cut around ground-nesting birds
  9. Tall grass and electric mower questions
  10. Can an electric mower cut really tall grass?
  11. Why does my cordless mower keep shutting off in tall grass?
  12. How many passes does it take to mow tall grass?
  13. Can you mow wet tall grass with a cordless mower?
  14. Does tall grass dull a mower blade faster?

Mow tall grass with an electric mower by raising the deck high and cutting in several passes. Slow your walking pace, take narrow strips and let the motor recover between heavy sections. Lower the deck for a final pass only after the first cut has dried and settled.

  • Set the deck at its highest position for the first pass through tall grass.
  • Remove no more than about a third of the grass height in one pass.
  • Take half-width strips and walk slowly so the motor keeps its speed.
  • Remove the battery or unplug the cord before touching the blade or chute.
  • Walk the area first to check for rocks, sticks, nests and hidden animals.

Why tall grass strains an electric mower

Tall grass strains an electric mower because the blade must cut more material in every turn. The motor draws extra power to hold blade speed against that load. A cordless mower turns the extra draw into shorter battery runtime. A corded model may slow down and lose cutting speed under the same strain.

Many electric mowers have lighter decks and smaller cutting widths than gas models. A light deck can ride up over dense stems and leave a ragged cut. Wet or matted grass adds weight and sticks to the underside of the deck. Each of these factors calls for a slower, more patient approach.

Grass that has gone to seed also has tougher, woody stems near the base. Prairie grasses and mature lawn grass can bend under the blade instead of cutting cleanly. A sharp blade slices those stems with less effort from the motor. Checking blade sharpness before a tall-grass job saves battery and gives a cleaner finish.

Walking the area before you start mowing

Walking the area before mowing tall grass reveals hazards the blade cannot handle. Tall grass hides rocks, branches, wire, toys and stakes that can bend a blade or fly out. Pick up loose objects and mark anything fixed, such as stumps or irrigation heads. Low spots and holes also deserve a marker, since they can tip the mower or twist an ankle.

Animals shelter in tall grass, so a slow walk-through gives them time to move. Rabbits, snakes, toads and ground-nesting birds may stay hidden until something comes close. Walking the strip in a pattern flushes many of them before the blade arrives. A found nest or den can be flagged and left with a wide uncut margin.

Dry grass is easier for an electric mower to cut than damp or wet grass. Dry stems cut cleanly, discharge well and put less strain on the motor. Wet grass clumps, clogs the chute and can make footing slippery. Waiting until dew or rain has dried off makes every later step easier.

Setting the deck height for the first cut

The deck height for the first pass through tall grass should be the highest setting available. A high deck lets the blade take only the top portion of the stems. The motor then handles a lighter load and keeps its blade speed. Grass that stands taller than the raised deck may still need extra passes.

Lawn care follows a guideline called the one-third rule for cutting height. The rule means removing no more than about a third of the grass height at one time. Cutting more at once stresses the grass and overloads the mower. Very tall grass may need several cuts, spaced out so the grass recovers between them.

A level deck matters on uneven ground, even at the highest setting. A tilted deck can scalp humps, which means cutting down to bare soil on high spots. Adjusting all wheels to the same setting keeps the cut level. Some mowers use a single lever, while others need each wheel set separately.

Cutting tall grass in passes, step by step

Cutting tall grass in passes means taking the height down in stages rather than all at once. The first pass removes the top of the stems at the highest deck setting. A second pass at a lower setting brings the grass closer to its final height. Some jobs need a third pass after the cut grass has dried and stood back up.

Narrow strips keep the load on an electric mower motor within a range it can handle. Overlapping each row by about half the deck width means the blade cuts less new grass per stride. A slow walking pace gives the blade time to clear the material in front of it. Listening to the motor helps, since a dropping pitch signals that you should slow down or back up.

Clipping settings on an electric mower affect how easily it handles tall grass. Side or rear discharge spreads the cut material instead of packing it into a bag. Mulching mode, which chops clippings finely and drops them back down, can overload the deck in long grass. Raking heavy clumps after the first pass keeps them from smothering the grass below.

  • Walk the area and remove hazards.
  • Raise the deck to its highest setting.
  • Mow narrow, half-width strips at a slow pace.
  • Rake or spread heavy clumps of clippings.
  • Let the grass dry and stand back up.
  • Lower the deck one step and mow again.

Stretching battery runtime on a cordless mower

Battery runtime on a cordless mower falls when the grass is tall, thick or damp. Manufacturers rate runtime for normal mowing conditions, not heavy cutting. A battery that covers a whole lawn in light grass may cover only part of it in tall growth. Planning the job in sections avoids stopping halfway through a strip.

A second charged battery lets you swap and continue while the first one recharges. Batteries from one tool platform often fit other tools of the same brand, which may already be on hand. Charging both batteries fully before the job starts keeps the work moving. Owner manuals often advise letting a hot battery cool before it goes back on the charger.

Some cordless mowers include a power boost mode for dense or tall grass. Higher power settings cut through tall stems more easily but drain the battery faster. Self-propelled drive also draws power, so pushing by hand can extend runtime on flat ground. The owner manual shows which features your model offers and how they affect battery use.

Using a corded electric mower in tall grass

A corded electric mower avoids runtime limits, but tall grass still strains its motor. The cord supplies steady power, so you can work as long as the motor stays cool. Thermal overload protection may stop the motor when it overheats from heavy cutting. Letting the mower rest before restarting gives the protection time to reset.

Cord management takes more attention in tall grass because the cord hides easily. Starting near the outlet and mowing away from it keeps the cord behind you on cut ground. Flipping the cord onto the cut side after each row keeps the mower from crossing it. Tall grass can conceal a cord loop, so look down before each turn.

A corded electric mower should only cut dry grass, because water and electricity create a shock risk. Use an outdoor-rated extension cord of the gauge the manual specifies. Plug the cord into an outdoor outlet with residual-current or ground-fault protection. A damaged cord needs replacing, and any outlet fault needs a qualified electrician.

FactorCordless mowerCorded mower
Working time in tall grassLimited by battery chargeLimited by motor heat
MobilityNot tied to an outletLimited by cord length
Extra care pointBattery heat and chargingCord placement and moisture
Power for dense grassBoost mode on some modelsSteady supply from the outlet

Clearing clogs and damaged blades safely

Clearing a clogged electric mower starts with removing the battery or unplugging the cord. Releasing the handle bar alone leaves the mower able to restart if the switch is bumped. Wait until the blade has stopped completely before reaching near the deck. Heavy work gloves protect your hands from the sharp edge of the blade.

Wet clumps under the deck reduce airflow and make the motor work harder. A plastic scraper or wooden stick clears packed grass without scratching the deck. Tip the mower only in the direction the manual shows, to protect the battery and motor. Clearing buildup between passes helps each later cut stay clean.

A blade that hits a hidden rock or root needs an inspection before mowing continues. A bent or chipped blade causes vibration and can damage the motor shaft. Sharpening or replacing a blade suits someone with the proper tools, or a mower repair service. Running the mower with a damaged blade puts the operator and bystanders at risk.

Timing the cut around ground-nesting birds

Mowing tall grass at the right time protects ground-nesting birds that raise young in prairie grass. Species such as meadowlarks, bobolinks and some sparrows build nests on or near the ground. A mower passing through during nesting can destroy eggs and kill chicks that cannot fly yet. Delaying the cut until young birds have fledged, meaning left the nest, lowers that risk.

Nesting seasons for grassland birds differ by region and species, so timing varies from place to place. A local bird club or wildlife organization can describe the nesting window in your area. Adult birds carrying food or flushing repeatedly from one spot often signal an active nest. Holding off on mowing that patch gives the brood time to leave.

The mowing pattern in tall grass decides whether wildlife can escape the blade. Cutting from the center outward lets animals move toward uncut cover at the edges. Mowing in from the edges can trap them in a shrinking island of grass. Leaving an uncut strip or corner provides shelter and seeds for birds across the seasons.

Tall grass and electric mower questions

Can an electric mower cut really tall grass?

Yes, an electric mower can cut tall grass if you raise the deck and work in several passes. Very tall or woody growth may exceed what a walk-behind mower handles well. A string trimmer or brush cutter can bring that growth down to a mowable height first.

Why does my cordless mower keep shutting off in tall grass?

A cordless mower shuts off in tall grass when the motor or battery overheats from heavy load. Raising the deck, taking narrower strips and slowing your pace reduce the strain. A cooled battery and a cleared deck often let the mower run again.

How many passes does it take to mow tall grass?

The number of passes for tall grass depends on its starting height and the height you want to reach. Each pass should remove no more than about a third of the remaining height. Grass standing far above the target height may need three or more separate cuts.

Can you mow wet tall grass with a cordless mower?

Yes, some cordless mowers can handle wet tall grass, but check the owner manual first. Some models advise against mowing in wet conditions to protect the motor and battery. Wet clippings also drain the battery faster and leave a rougher finish. Slippery footing on wet ground raises the risk of a fall near the blade.

Does tall grass dull a mower blade faster?

Yes, tall, thick or seed-heavy grass can dull a mower blade faster than routine mowing. Hidden sticks, sand and small stones add wear on top of the extra cutting. A dull blade tears stems, which leaves ragged brown tips and drains more power. Inspecting the blade after a tall-grass job shows whether it needs sharpening.

Latest articles