How to Make Field Recordings: Getting Started
Learn how to make field recordings from the first session on: choosing a location, setting recording levels, and capturing clean ambient sound with simple gear.
Contents
- What field recording involves
- Choosing a recording location
- Setting recording levels
- Microphones and wind protection
- Your first recording session
- Field notes and file naming
- Listening back and improving
- Questions About Field Recording
- How do I get started with field recording?
- How do I make field recordings that sound clean?
- What gear do I need for a first recording session?
- When is the best time of day to record birdsong?
- How do I keep wind from ruining outdoor recordings?
- Should I write notes during a field recording session?
Making a field recording means capturing the sound of a place with a microphone and a recorder, away from a studio. You start by choosing a quiet location, setting conservative recording levels, and listening before you press record. The first session matters less than the habit of returning to the same spot and learning how the soundscape changes.
- Choose a location for its quiet and its character, then visit it before you record.
- Set recording levels low enough that loud surprises do not distort the file.
- Listen with headphones during the take so you hear what the microphone hears.
- Note the time, weather and direction of each take so you can compare sessions later.
- Keep the first session simple: one recorder, one microphone, one place.
What field recording involves
Field recording is the practice of capturing ambient sound outside a studio, from birdsong and wind to water and distant traffic. The recording chain is short: a microphone turns air pressure into a signal, a recorder stores that signal as a file, and headphones let you monitor it. Everything else in field recording basics follows from those three pieces working together.
The goal of ambient sound capture is a believable sense of place rather than a clean studio sound. Wind, distant engines and your own footsteps are part of what a listener hears, so you decide which of them belong in the recording. A take with some texture often says more about a place than a silent one.
Your first recording session does not need expensive gear, but it does need patience. Plan to stand still for a while and let the soundscape settle after your arrival. Many recordings fail because the recordist left before the place became itself again.
Choosing a recording location
Choosing a recording location starts with quiet, but quiet alone is not enough for an interesting file. Look for a place with a clear character, such as a marsh edge, a grove of trees or a stretch of grassland, and check how far it sits from roads and machinery. A location with one strong sound source is easier to record than a crowded one.
Visit the place once without gear and simply listen for a while. Note which sounds arrive and fade, where the wind comes from, and whether aircraft or traffic pass overhead. A visit in the same season and at the same hour as your planned session tells you more than any map.
Access and permission matter as much as acoustics. Confirm that you may stand and record where you plan to be, and keep your distance from nests, dens and other sensitive spots. A location you can reach again easily is worth more than a dramatic one you visit once.
Setting recording levels
Recording levels set how strongly the signal is written to the file, and they decide whether a loud gust ruins the take. Aim for peaks that stay well below the maximum, leaving headroom for sudden sounds. Digital recorders show levels in decibels relative to full scale, written as dBFS, where zero is the ceiling.
Set the gain, the amount of amplification applied to the microphone signal, before the quietest passage you expect. Watch the meter during a test and lower the gain if peaks approach the ceiling. A slightly quiet file can be raised later, but a distorted one cannot be repaired.
Use the recorder limiter only as a backstop, because it changes loud transients rather than preventing them. Check levels again whenever you move to a new spot or the wind rises. Write down the gain setting for each take so a later session can match it.
Microphones and wind protection
Microphone choice shapes the sound of a field recording more than the recorder does. A directional microphone favors what it points at and rejects sound from the sides, while a spaced pair captures a wider scene. An omnidirectional microphone picks up everything around it and suits a still, open place.
Wind protection is not optional outdoors, because air moving across a capsule creates low rumble that swamps the file. A foam cover handles a breeze, and a fur-covered windshield handles stronger gusts. Place the microphone clear of surfaces that reflect sound, and keep your body between the wind and the capsule where you can.
Cables and connectors deserve a check before every session. Carry a spare cable and test the whole chain at home, so a loose connection does not end a morning in the field. Label your cables and store them coiled so they unfold without tangling.
Your first recording session
A first recording session goes smoothly when you arrive early and set up before the soundscape is at its liveliest. Switch on the recorder, arm it, and record a minute of silence with the microphone covered. That test take shows the noise floor, the steady hiss of the equipment itself, which you subtract from what you hear later.
Record longer takes than you think you need, and note the start time of each one. Stand still, breathe quietly and avoid handling the recorder while it runs. If a plane or a car passes, keep recording and mark the moment, because the clean passage before it may still be useful.
At the end of the session, play back one take through headphones before you pack up. Confirming that the file holds sound and not just noise saves a wasted trip. Then write a short note about the weather, the hour and anything that dominated the scene.
Field notes and file naming
Field notes turn a folder of audio files into a record you can use and compare. For each take, write the place, the date, the hour, the weather and the direction the microphone faced. A note about a distant highway or a barking dog explains a sound that would otherwise puzzle you months later.
Name files in a consistent pattern so they sort in the order you recorded them. A simple scheme of place, date and take number works without special software. Keep the notes and the audio files together, and back up both to a second drive after the session.
Comparing takes from the same place across seasons is one reward of careful notes. Birdsong shifts through the year, and a record of the same spot in spring and late summer shows that change. The prairie soundscape rewards the recordist who returns.
Listening back and improving
Listening back is where a recordist learns what the microphone actually captured. Play the files on quiet speakers or headphones and listen for handling noise, wind rumble and the hum of the recorder. Mark the moments worth keeping and note what you would change next time.
Simple editing can raise the level of a quiet take and trim the ends of a file. Filtration that removes low rumble helps a windy recording, but heavy processing flattens the sense of place. Keep an unedited copy of every original file.
The next session builds on what the last one taught you. Change one thing at a time, such as the microphone position or the hour of your visit, so you can tell what made the difference. A field recording practice grows from these small, repeated experiments.
Questions About Field Recording
How do I get started with field recording?
Getting started with field recording takes a recorder, a microphone and headphones, plus one quiet place you can revisit. Learn the level controls at home and record a short take in your yard before traveling farther. The first aim is a clean file and a habit, not a finished soundscape.
How do I make field recordings that sound clean?
A clean field recording comes from conservative levels, good wind protection and a still microphone. Set gain so peaks stay well below the ceiling and monitor with headphones during the take. Wind rumble and handling noise spoil more files than the recorder itself does.
What gear do I need for a first recording session?
A portable recorder, a microphone with a windshield and a pair of closed headphones cover a first session. Carry spare batteries, a spare cable and a notebook for field notes. A tripod or a small stand helps you keep the microphone still and your hands off the recorder.
When is the best time of day to record birdsong?
Early morning holds the densest birdsong in many places, when light is low and the air is still. Dawn also brings less wind and fewer people than midday. Visit your chosen spot at several hours before you commit, because each place has its own rhythm.
How do I keep wind from ruining outdoor recordings?
Wind protection is the first defense: use a foam cover for a breeze and a fur windshield for stronger gusts. Position the microphone so your body or a natural shelter blocks the wind. Reduce low-frequency rumble in editing only after you have captured the cleanest take you can.
Should I write notes during a field recording session?
Field notes are essential, because they explain sounds you will not recognize later. Record the place, hour, weather and any passing noise for every take. Notes also let you compare the same location across seasons and hear how the soundscape changes.