PRAIRIE FIELD NOTES / MONTANA

How to Make a DIY Ground Cloth, Ground Sheet or Tarp for Tents

Learn how to make a DIY ground cloth, ground sheet or tarp for tents: choose waterproof fabric, cut and hem it, add tarp grommets, and seal the seams.

8 min read0 viewsHow to Make a DIY Ground Cloth, Ground Sheet or Tarp for Tents
— · 0 votes
Contents
  1. Measure the space the cloth must cover
  2. Choose a waterproof fabric for the job
  3. Cut the fabric cleanly and squarely
  4. Hem the edges to stop fraying
  5. Add grommets or loops for tie-outs
  6. Seal the seams and stitching
  7. Care for the cloth between trips
  8. Pitch the cloth so rain runs off
  9. Questions about DIY tent ground cloths
  10. Can I make a DIY ground sheet without sewing?
  11. What size should a DIY tent ground cloth be?
  12. What is the best fabric for a DIY ground cloth?
  13. Do I need grommets on a DIY ground cover?
  14. How do I stop water coming through the seams of a DIY ground sheet?
  15. Can a DIY ground cloth double as a tarp?

You can make a DIY ground cloth for a tent by cutting a waterproof fabric slightly smaller than your tent floor, hemming the edges, and adding tie-out points. The same approach works for a DIY ground sheet under a sleeping pad or a plain tarp for a sitting area. The job is mostly measuring, cutting and a little sealing, not advanced sewing.

  • Cut the cloth a little smaller than the tent floor so rain runs off instead of puddling under the tent.
  • Pick a waterproof fabric by weight and pack size, not by brand claims.
  • Fold and sew a hem, then seal the stitching to keep water from wicking through.
  • Add tarp grommets or fabric loops at the corners for guylines and stakes.
  • Inspect the cloth after each trip and patch pinholes before they grow.

Measure the space the cloth must cover

A DIY ground cloth works only when it matches the footprint it protects. Set up the tent on flat ground or lay out its floor plan on paper, then measure the length and width of the floor. Write the numbers down before you cut any fabric.

Cut the ground cloth slightly smaller than the tent floor, with a margin of a few inches less on every side. A cloth that sticks out past the tent edge catches rain and channels water under the floor. A tent footprint follows the same rule, so keep the edges tucked inside.

For a ground sheet under a sleeping pad or a tarp for a sitting area, measure the open space you want to cover instead. Leave extra fabric where you plan to fold the edges back. Mark the outline with chalk or a washable marker before cutting.

UseSize relative to the spaceEdge treatment
Tent ground clothA few inches smaller than the floor on each sideHem and seal
Sleeping pad ground sheetMatches the pad plus a hand widthSimple hem
Sitting or gear tarpCovers the area you use, with fold-back edgesHem and corner loops

Choose a waterproof fabric for the job

Groundsheet materials decide how the finished cloth feels, packs and wears. A coated nylon or polyester ripstop is light and packs small, which suits a tent ground cloth. A heavier coated fabric resists abrasion better under a floor that sees boots and gear.

Look for fabric sold as waterproof fabric with a coated back, not water-resistant cloth. Water-resistant fabric sheds light rain but lets pressure push moisture through. The coating is what keeps groundwater out when you kneel or sleep on the cloth.

Compare candidates by weight per area, packed size and stiffness. A stiffer fabric lies flat and is easier to fold and stake, while a thin fabric saves space in a pack. Check that the fabric can be sewn without cracking at the fold.

  • Coated nylon ripstop: light and small to pack
  • Coated polyester: stable and resistant to stretching
  • Heavier coated fabric: stands up to abrasion
  • Water-resistant cloth: sheds rain but not ground pressure
  • Scrap fabric or an old tarp: low cost, check for holes

Cut the fabric cleanly and squarely

A square cut keeps a DIY ground cover lying flat and folding evenly. Lay the fabric on a clean floor, weight the corners and pull out wrinkles before marking. Use a long straightedge and a sharp blade or fabric shears.

Cut along the marked line in one steady pass so the edge does not fray or wander. Coated fabric can dull a blade quickly, so change the blade when the cut starts to drag. Keep the offcut for patches and small repair pieces.

Mark the top side of the cloth with a small chalk mark before you move it. The coated side faces the ground, and knowing which side is which helps when you sew the hem and seal the seams. A labeled corner also speeds up pitching later.

Hem the edges to stop fraying

Hemming a ground cover gives the edge strength and stops woven fabric from unraveling. Fold the edge over a short width, press it flat and fold it once more so the raw edge is hidden. Pin or clip the fold along the whole side.

Sew the hem with a straight stitch close to the inner fold, then run a second line near the outer edge on heavy fabric. A short stitch length holds better on coated cloth than a long one. Go slowly around corners so the needle does not skip.

Where you cannot sew, a folded hem held with fabric adhesive or iron-on tape can work on some coated fabrics. Test the bond on a scrap piece first, because heat and adhesive behave differently on each coating. A weak hem fails at the corner, so reinforce those spots.

Add grommets or loops for tie-outs

Tarp grommets and fabric loops let you stake the cloth or tie it to a pack. Mark the tie-out points at each corner and, on a large cloth, at the middle of each side. Space them so the cloth stays taut without stretching the fabric.

For a grommet, fold a small reinforcement patch of the same fabric over the marked spot and punch through both layers. Set the grommet with its tool so the two halves clamp the fabric firmly. A grommet set into a single layer can tear out under load.

For a fabric loop, sew a short strip of webbing or folded fabric into the hem at each point. Leave a loop big enough for a stake or a cord. Stitching through several layers by hand needs a sturdy needle and pliers to push it through.

Seal the seams and stitching

Seam sealing keeps water from wicking through the needle holes along a hem. Apply a seam sealer made for the fabric coating on the stitched side after the sewing is done. Work in a ventilated space and let the sealer cure fully before folding the cloth.

Spread a thin, even line over each row of stitching rather than a thick blob. A heavy layer skins over and stays tacky underneath. Thin sealer reaches into the holes and bonds to the coating.

Check the sealed seams by holding the cloth up to light and looking for gaps. Touch up thin spots and any spot where the sealer pulled away from the fabric. Sealing also helps hemming and seam sealing hold together over repeated folding.

Care for the cloth between trips

Tent floor protection depends on the cloth staying free of holes and grit. Shake out sand and needles before folding, because grit grinds the coating at every fold. Wipe the cloth with a damp cloth and let it dry completely before storage.

Fold the ground cloth loosely along the same lines each time and store it away from sharp tools. A stuff sack keeps it separate from stakes and cookware. Sharp edges in a pack are what puncture a coated fabric.

Inspect the cloth after each trip for pinholes and worn corners. Patch small holes with a piece of the offcut and flexible adhesive made for coated fabric. Replace the cloth when the coating peels over a large area.

Pitch the cloth so rain runs off

A DIY tent ground cloth stays dry when its edges sit inside the tent floor line. Tuck any overhang under the floor or fold it back before you stake the tent. Water that collects on an exposed edge finds its way under the floor.

On soft ground, stake the corners through the grommets so the cloth cannot shift while you set up the tent. Keep the cloth flat and free of wrinkles under the floor. A wrinkle becomes a channel for water and a wear point for the floor.

A tarp used as a sitting or gear cover can be pitched with a slight slope and a low edge away from the wind. Peg the corners and lift the middle with a pole or a line to a tree branch. Leave the downhill edge open so water drains away from the covered area.

Questions about DIY tent ground cloths

Can I make a DIY ground sheet without sewing?

Yes, a DIY ground sheet can be made without sewing by folding the edges and bonding them with fabric adhesive or iron-on tape. Test the bond on a scrap of the same coated fabric first. Reinforce corners with patches and set grommets through folded layers.

What size should a DIY tent ground cloth be?

A DIY tent ground cloth should be a few inches smaller than the tent floor on every side. The smaller size lets rain run off the tent instead of collecting on an exposed edge. Measure the floor after pitching the tent and cut to that outline.

What is the best fabric for a DIY ground cloth?

A coated nylon or polyester ripstop is a practical fabric for a DIY ground cloth because it is light and packs small. A heavier coated fabric suits rough ground and hard use. The key point is a waterproof coating, not the fiber name.

Do I need grommets on a DIY ground cover?

Grommets are optional on a small DIY ground cover but help on a large one. They give you points to stake the cloth and keep it from shifting during setup. Set each grommet through a folded reinforcement patch so it cannot tear out.

How do I stop water coming through the seams of a DIY ground sheet?

Seal the stitched seams of a DIY ground sheet with a sealer made for the fabric coating. Apply a thin line over each row of stitching and let it cure fully. Sealing closes the needle holes that otherwise let water wick through.

Can a DIY ground cloth double as a tarp?

Yes, a DIY ground cloth can double as a tarp when it has grommets or loops at the corners and sides. A coated fabric keeps rain out from above as well as below. Pitch it with a slope so water runs off rather than pooling.

Latest articles