Calculating a Telescope's True Field of View
Learn the true field of view formula, the field stop method and how to convert degrees to feet at 1000 yards, with worked telescope examples.
Contents
- True field versus apparent field of view
- The true field of view formula step by step
- The field stop method for a more exact result
- Converting degrees to feet at 1000 yards
- Measuring true field on the sky by drift timing
- How field of view calculators do the math
- Planning views with true field and exit pupil
- Telescope true field of view questions
- How do I work out the true field of view of my telescope?
- What is the difference between apparent and true field of view?
- How many feet does one degree cover at 1000 yards?
- Are online field of view calculators accurate?
- Does a higher power eyepiece always give a narrower field?
- Why does the field stop give a more accurate true field?
To calculate a telescope's true field of view, divide the eyepiece apparent field of view by the magnification. Magnification itself equals the telescope focal length divided by the eyepiece focal length. For a sharper figure, divide the field stop diameter by telescope focal length, then multiply by 57.3.
- Magnification equals telescope focal length divided by eyepiece focal length.
- True field equals the eyepiece apparent field divided by magnification.
- The field stop method gives a more exact true field than the apparent field method.
- Multiply true field in degrees by 52.4 to get feet across at 1000 yards.
- Timing a star's drift across the view checks any calculated field on the sky.
True field versus apparent field of view
True field of view is the slice of sky or landscape a telescope actually shows you. Observers measure it in angular degrees, the same units used to describe the size of the Moon. The full Moon spans roughly half a degree, which makes a handy mental yardstick. A true field of one degree would therefore fit about two Moons side by side.
Apparent field of view is a property of the eyepiece alone, not of the telescope. Eyepiece makers print the figure in degrees, and it describes how wide the circle of light looks. A simple eyepiece design might show an apparent field of 40 to 50 degrees. Wide-angle designs can reach 80 degrees or more, which feels like looking through a large window.
Magnification is the link between apparent field and true field in any telescope. The telescope enlarges the scene, so the wide apparent circle holds only a small piece of real sky. Higher power shrinks the true field, while lower power widens it with the same eyepiece design. Knowing both numbers lets you predict what fits in the view before you look.
The true field of view formula step by step
The basic true field of view formula divides the eyepiece apparent field by the magnification. Start by finding magnification: telescope focal length divided by eyepiece focal length. Both focal lengths are normally printed in millimeters, so the units cancel out. The result is a plain number written with an x, such as 40x.
A worked example makes the true field of view formula concrete. A telescope with a 1000 mm focal length and a 25 mm eyepiece gives 40x magnification. If that eyepiece has a 50 degree apparent field, the true field is 50 divided by 40. The answer is 1.25 degrees, enough to frame the full Moon with room to spare.
The apparent field method of calculating true field is quick but only approximate. Eyepiece makers sometimes round the apparent field, and some designs add distortion near the edge. Errors grow with wide-angle eyepieces, where the stated figure can differ noticeably from the real one. Treat the result as a close estimate rather than an exact measurement.
- Note the telescope focal length in millimeters
- Note the eyepiece focal length and apparent field
- Divide telescope focal length by eyepiece focal length for magnification
- Divide the apparent field by the magnification
- Read the result as true field in degrees
The field stop method for a more exact result
The field stop method calculates true field from the eyepiece's internal opening rather than its rated apparent field. A field stop is the metal ring inside the eyepiece barrel that sharply bounds the view. Its diameter, together with telescope focal length, fixes the true field without relying on apparent field ratings. Some eyepiece makers publish the field stop diameter in millimeters.
Dividing the field stop diameter by the telescope focal length gives true field in radians. Multiply that ratio by 57.3, the number of degrees in one radian, to convert it to degrees. A 27 mm field stop in a 1000 mm telescope gives 27 divided by 1000, times 57.3. The true field in that example comes out at about 1.55 degrees.
Field stop diameter can be estimated when the maker does not publish it. Multiply the eyepiece apparent field by the eyepiece focal length, then divide by 57.3. A Barlow lens multiplies the effective telescope focal length, while a focal reducer shortens it. Use the adjusted focal length in the formula whenever either accessory sits in the light path.
Converting degrees to feet at 1000 yards
Linear field of view expresses the same view as a width in feet at a set distance. Binocular and spotting scope makers often state it as feet at 1000 yards. Birders compare these figures when choosing optics for open prairie or shorebird flats. Converting between angular and linear field takes one multiplication or division.
To convert field of view degrees to feet at 1000 yards, multiply the degrees by 52.4. The factor comes from 3000 feet times the tangent of one degree. A true field of 1.25 degrees therefore covers about 65 feet at that distance. Going the other way, divide feet at 1000 yards by 52.4 to get degrees.
Metric spec sheets give linear field as meters at 1000 meters instead. Multiply degrees by 17.5 to get meters at 1000 meters. Linear field scales with distance, so halving the distance halves the width you see. For another distance in yards, multiply degrees by the distance and by 0.0524 to get feet.
| True field (degrees) | Feet at 1000 yards (approx.) | Meters at 1000 meters (approx.) |
|---|---|---|
| 0.5 | 26 | 9 |
| 1 | 52 | 17 |
| 2 | 105 | 35 |
| 4 | 210 | 70 |
| 6 | 315 | 105 |
| 8 | 420 | 140 |
Measuring true field on the sky by drift timing
Star drift timing measures true field directly, without trusting any printed specification. Earth's rotation carries stars across the view at a steady, known rate. The celestial equator is the projection of Earth's equator onto the sky. A star on the celestial equator moves one degree every four minutes of time.
Aim at a bright star and switch off any tracking motor before timing a drift. Position the star so it will drift straight through the center of the field. Start a stopwatch as the star enters the view and stop it as the star leaves. Repeat the timing a few times, then average the results for a steadier figure.
The drift formula multiplies the drift time in minutes by 0.25 to get degrees. For stars away from the celestial equator, also multiply by the cosine of the star's declination. Declination is a star's angle north or south of the celestial equator. Choosing a star close to the equator keeps the correction small and the math simple.
How field of view calculators do the math
A telescope field of view calculator runs the apparent field or field stop formula on numbers you enter. Typical inputs are telescope focal length, eyepiece focal length and apparent field or field stop. Many tools also report magnification, exit pupil and linear field at a chosen distance.
General optics field of view calculators often serve cameras rather than eyepieces. Their inputs include sensor size, lens focal length and working distance to the subject. Working distance is the gap from the front of the lens to the object. Check that a calculator asks for eyepiece data before using it for a telescope.
A calculator result is only as good as the specifications fed into it. Rounded apparent field ratings carry their error straight into the answer. Field stop inputs, where a tool accepts them, produce a closer figure. Working the formula by hand once helps you spot an input mistake or a unit mix-up.
Planning views with true field and exit pupil
True field helps you choose an eyepiece for a target before you set up. Large star clusters and wide nebulae need a low power with a generous true field. Small planets and double stars tolerate a narrow field at higher magnification. On a spotting scope, a wider true field makes it easier to find a moving bird.
Exit pupil is the diameter of the beam of light leaving the eyepiece. Aperture, the diameter of the main lens or mirror, sets the size of that beam. Divide telescope aperture by magnification to find exit pupil in millimeters. A 100 mm aperture at 40x gives an exit pupil of 2.5 mm.
Low power widens the true field but also enlarges the exit pupil. An exit pupil larger than your eye's own pupil wastes part of the telescope's aperture. The widest true field a telescope can show depends on the largest field stop its focuser accepts. A 2-inch focuser, the drawtube that holds the eyepiece, passes a larger field stop than a 1.25-inch one.
Telescope true field of view questions
How do I work out the true field of view of my telescope?
Divide the eyepiece apparent field by the magnification to get the telescope's true field in degrees. Magnification is the telescope focal length divided by the eyepiece focal length. A 600 mm telescope with a 20 mm eyepiece of 60 degrees shows 2 degrees of sky.
What is the difference between apparent and true field of view?
Apparent field is how wide the eyepiece view looks to your eye, measured in degrees. True field is the actual width of sky or land the telescope shows. Magnification connects the two, since true field equals apparent field divided by magnification.
How many feet does one degree cover at 1000 yards?
One degree of field covers about 52.4 feet at 1000 yards. The figure equals 3000 feet times the tangent of one degree. Multiply any true field in degrees by 52.4 for its linear width at that range.
Are online field of view calculators accurate?
A field of view calculator is accurate only to the quality of the numbers you enter. Apparent field ratings are often rounded, which carries a small error into the result. Calculators that accept field stop diameter give a closer figure.
Does a higher power eyepiece always give a narrower field?
No, a higher power eyepiece does not always give a narrower true field. A wide-angle eyepiece at higher power can match the field of a narrow eyepiece at lower power. Running the true field formula for each eyepiece shows the real comparison.
Why does the field stop give a more accurate true field?
The field stop gives a more accurate true field because it is the physical edge of the view. Apparent field ratings can be rounded or skewed by edge distortion in the eyepiece. Dividing field stop diameter by telescope focal length avoids both problems.