# Scotts Broadcast Spreaders for Grass Seed

How a Scotts broadcast spreader throws grass seed, how to set the rate, and how to cover a prairie lawn or plot evenly without streaks or waste.

A Scotts broadcast spreader is a walk-behind drop-style machine that flings grass seed outward in an arc as you push it. The spinning impeller under the hopper throws seed over a wide strip, so you cover ground faster than with a drop spreader. Getting an even stand depends on the spreader setting, your walking pace, and how you overlap each pass. 

- A broadcast spreader throws seed in an arc, so it covers a wide strip per pass rather than a narrow band.
- The hopper gate setting controls how much seed leaves the hopper, and the impeller controls how far it flies.
- Calibrating the gate on a small test area tells you the real rate for your seed lot more reliably than the label alone.
- Overlapping each pass by part of the swath width is what prevents streaks and bare strips.
- Grass seed is light and irregular, so a steady walking pace matters as much as the setting.
 

## What a Scotts broadcast spreader does 

A Scotts broadcast spreader carries seed in a hopper and drops it onto a spinning impeller beneath the hopper opening. The impeller flings the seed outward in a fan-shaped arc, so each pass covers a strip wider than the machine itself. This is the difference between a broadcast spreader and a drop spreader, which releases seed straight down in a narrow band. 

The hopper gate sets how wide the opening is, and that opening controls the flow of seed onto the impeller. A lever on the handle lets you open and close the gate while you walk. The impeller speed is set by the drive, so pushing at a steady pace keeps the throw pattern consistent. 

Grass seed is light, flat, and irregular in shape, which makes it behave differently from fertilizer pellets. Seed tends to flutter and drift more than round granules, so wind and walking speed change the pattern more. A broadcast spreader still handles grass seed well when you keep the pace even and overlap your passes. 

## Reading the spreader settings 

Spreader settings on a Scotts broadcast spreader are numbers on the gate lever that correspond to a flow rate. The number itself means little without the seed you are using, since a light seed and a heavy seed flow differently at the same setting. Treat the setting as a starting point, not a fixed rule. 

Seed bags often print a suggested spreader setting for the brand and model, and that suggestion is the place to begin. Because grass seed varies in size and weight between lots and species, the printed number may need adjustment. A short test run shows whether the gate is releasing too much or too little for your seed. 

Keep a note of the setting you settle on for each seed type you sow. A record of gate number, pace, and overlap width lets you repeat a good result next season. Spreader settings are a reference you build for your own machine and your own seed. 

## Calibrating the gate before you sow 

Calibration means measuring how much seed the spreader actually releases at a given gate setting over a measured area. Fill the hopper with a known weight of seed, open the gate at your chosen setting, and push over a small measured strip. Weigh what is left to see how much went out. 

Compare that release rate with the seeding rate your grass seed calls for. Adjust the gate up or down and repeat the short run until the flow matches the target. Calibration on a small area costs a little seed and saves a whole lawn from being too thin or too thick. 

Do the calibration on a hard surface or a tarp so you can recover and reuse the seed. Wind can spoil the measurement, so pick a still day for the test. Once the gate is set, mark the lever position so you can return to it. 

## Walking pace and overlap pattern 

Even coverage from a broadcast spreader depends on a steady walking pace and a deliberate overlap between passes. Push at the same speed you used during calibration, because a faster walk thins the seed and a slower walk thickens it. Stop moving and the seed piles up in one spot. 

Overlap each pass by part of the swath width so the thin edges of one strip meet the thin edges of the next. A broadcast spreader throws heaviest in the middle of its arc and lighter at the edges, so the overlap fills the gaps. Many guides suggest splitting the application into two passes at right angles for a more even stand. 

Turn the spreader off at the end of each pass and at corners to avoid dumping seed in one place. Keep the gate closed while you reposition the machine. Marking your passes with stakes or a light line helps you keep the overlap consistent. 

## Choosing a Scotts spreader model 

Scotts broadcast spreaders come in push models and tow-behind models, and the choice depends on the size of the area you seed. A push spreader suits a lawn or a small prairie plot where you can walk the ground. A tow-behind spreader suits larger open ground where a vehicle can pull it. 

Hoppers differ in capacity, and a larger hopper means fewer refills on a big area. Handle and gate designs differ too, and a smooth lever action makes it easier to hold a steady setting. Check that the model you pick lists grass seed among the materials it is meant to spread. 

Consider the impeller and the spread width the model produces, since a wider throw means fewer passes. Match the machine to the ground you have rather than to the largest model available. A spreader you can push comfortably at a steady pace will give a more even result than one that fights you. 
| Model type | Where it fits | What to check | 
| Push broadcast spreader | Lawns and small prairie plots you can walk | Hopper capacity and gate lever feel | 
| Tow-behind broadcast spreader | Large open ground a vehicle can cross | Hitch fit and spread width | 
| Drop spreader | Edges and narrow strips needing precise lines | Width of the drop band |  

## Handling grass seed in the hopper 

Grass seed flows best when the hopper is dry and the seed is free of clumps. Damp seed bridges over the gate opening and stops flowing, which leaves a bare strip behind the machine. Store seed in a sealed container and fill the hopper just before you start. 

Fill the hopper over a tarp or on the lawn so spilled seed is not wasted. Do not overfill past the level the hopper is designed to hold, since a heavy load can affect the gate action. Break up any clumps with your hands before the seed goes in. 

Clean the hopper and impeller after each use, because seed residue hardens and blocks the gate. A soft brush and a dry cloth remove most residue without damaging the parts. Follow the manufacturer's cleaning guidance for the model you own. 

## Sowing grass seed on prairie ground 

Grass seed sown on prairie ground needs contact with soil to germinate, and a broadcast spreader only places the seed on the surface. Raking or light harrowing after spreading brings seed into contact with the soil. Seed left on top of thatch or matted grass dries out and fails. 

Wind is the main hazard when broadcasting light grass seed on open prairie. Choose a still part of the day and keep the spreader low and the gate modest. A light mulch or a thin straw cover after sowing helps hold seed and moisture in place. 

Wildlife visits your seeded ground, so expect birds to take some surface seed before it settles. Working the seed into the soil soon after spreading reduces that loss. A prairie seeding benefits from sowing before a period of settled, mild weather rather than ahead of a heavy storm. 

## Spreader care and storage 

A Scotts broadcast spreader lasts longer when seed and residue are cleared from the gate and impeller after every use. Seed left in the hopper absorbs moisture and sets hard, which jams the gate on the next outing. Empty the hopper fully and brush out the corners. 

Check the impeller and the gate linkage for wear before each season. A bent impeller throws an uneven pattern, and a sticky gate makes the setting drift. Replace worn parts with the parts the manufacturer lists for your model. 

Store the spreader dry and with the gate closed and the hopper empty. Hanging or standing the machine so the impeller is off the ground keeps it from warping. A dry store protects the metal parts from rust between seeding seasons. 

## Questions about Scotts spreaders and grass seed 

### What Scotts broadcast spreader setting should I use for grass seed? 

The right Scotts broadcast spreader setting for grass seed depends on the seed lot and the model, so no single number fits every bag. Start with the setting printed on the seed bag for your spreader model. Then run a short calibration to confirm the flow matches the seeding rate your grass seed calls for. 

### Can I use a Scotts broadcast spreader for grass seed? 

Yes, a Scotts broadcast spreader can spread grass seed when the model lists seed among the materials it handles. Grass seed is light and irregular, so keep the walking pace steady and overlap each pass. Working the seed into the soil after spreading gives it the contact it needs to germinate. 

### How do I stop streaks when broadcasting grass seed? 

Streaks come from gaps between passes and from an unsteady pace, so overlap each strip by part of the spread width. Splitting the seed into two passes at right angles evens out the thin edges of the arc. Close the gate at turns and corners so seed does not pile up. 

### How much grass seed does a Scotts spreader hold? 

Hopper capacity differs between Scotts spreader models, so check the capacity listed for the model you own. A larger hopper means fewer refills across a big area. Fill only to the level the hopper is designed for and empty it after use. 

### Do I need to calibrate a new spreader before seeding? 

Yes, calibrating a new Scotts broadcast spreader before seeding tells you the real flow at each gate setting. Seed lots vary in weight and size, so the printed setting is only a starting point. A short measured test run on a tarp recovers the seed and shows whether the gate needs adjusting. 

### How should I clean a broadcast spreader after grass seed? 

Cleaning a broadcast spreader after grass seed means emptying the hopper and brushing residue from the gate and impeller. Seed left in place absorbs moisture and hardens, which jams the gate later. Store the machine dry with the gate closed and the hopper empty.
