# Infrasound Recording of Animals Outdoors

How to record animal infrasound outdoors: choosing an infrasonic sensor, placing it against wind noise, and reading low-frequency calls with care.

Recording animals with infrasound means capturing sound below the range of human hearing, where bird and mammal calls can travel far across open prairie. An infrasonic sensor works only when it is shielded from wind, mounted firmly and paired with a recorder that can store very low frequencies. The method rewards patience more than equipment cost. 

- Infrasonic sensors capture sound below the pitch range people hear, so you need a recorder that stores the full low-frequency signal.
- Wind noise at low frequencies can bury animal calls, so a foam and fabric shield or a buried mount does more for results than a costly sensor.
- Low-frequency microphones have wide pickup patterns, so the sensor points at the soundscape rather than a target species.
- Record the same spot on several quiet days, then slow the playback to hear what your ears miss.
 

## What infrasound is and where it occurs 

Infrasound sits below the lowest pitch a person can hear, and animals that use it produce calls far deeper than a bird's song. The air carries these low frequencies a long way over flat terrain, because the ground absorbs little of them. Prairie wind, distant thunder and the low pulse of a road also live in this range. 

An infrasonic sensor senses that pressure change and sends it to a recorder. The signal is not shaped like a whistle; it is a slow rise and fall you see on a waveform view instead of hear. Low-frequency microphone designs use a large, flexible diaphragm to catch these gentle waves. Look for a sensor whose stated low-frequency limit is well below the lowest sound you expect to capture. 

Animal infrasonic communication is studied in elephants and some whales, and the same physics lets low calls carry across grassland. Many birds also produce low drumming or booming sounds that sit near the bottom of the audible range. A sensor that records the low end of human hearing and below can document both. 

## Choosing an infrasonic sensor for field use 

A field-ready infrasonic sensor needs a low noise floor, a flat response through the low band and a weather-tight body. Ask how the sensor behaves in damp air and whether its output can feed your recorder without extra gain. Battery life and cable connectors matter less on short trips and more on overnight stays. 

Outdoor use puts stress on connectors and stands, so a metal-bodied unit with a sealed cap reduces trouble. Check that the sensor's output level suits your recorder input, because too much gain boosts wind noise as well as animals. A sensor with a built-in high-pass filter is useful, since it removes the deepest rumble and leaves the call band. 

Compare the options by the sound they are made for, not by brand names. A rugged low-frequency microphone suits fixed watches; a compact infrasonic sensor suits travel. Neither is needed if your recorder cannot store below twenty hertz cleanly. 

## Placing a sensor against wind noise 

Wind noise at low frequencies is the main obstacle to infrasonic recording outdoors, and placement controls it more than any setting. Mount the sensor low, close to the ground, where gusts are weaker than at shoulder height. Keep the body out of the direct air stream and avoid open crests on windy days. 

A simple windshield of open-cell foam wrapped in a loose fabric layer slows the air before it reaches the diaphragm. For fixed sites, a buried housing with a porous cover gives still air around the sensor. Burying a sensor may not suit a site where soil protection rules apply, so check local land rules first. 

Cable movement also produces low-frequency thumps, so tape the lead to the stand and leave a slack loop. Point the sensor at open sky or flat ground and keep hard surfaces such as canvas and vehicle panels away. A small wind break of packed earth or short grass can help without blocking the sky. 

## Recording and monitoring low frequencies 

Low-frequency recording needs a high sample rate and a format that keeps the signal intact. Set the recorder to the highest rate available and monitor with headphones that reproduce deep sound. Many headphone sets roll off the bottom end, so trust a spectrum view as well as your ears. 

Watch the level meter closely, because a slow low wave can push a meter far less than it pushes a speaker. Keep peaks below clipping and avoid heavy gain on the sensor, since that lifts the wind floor and hides the animal. Write down the time, weather and place for each take, so a later listen has context. 

Infrasonic calls may sit outside your hearing entirely, so review each file in software that shows the spectrogram and slow playback. Speeding up a recording raises pitches into the audible band while keeping the rhythm of the call. Slow playback helps you judge the shape of a boom or a rumble, and a waveform view shows sudden thumps from the stand. 

## Recognizing low animal sounds on the prairie 

Low animal sounds on the prairie often arrive as rhythmic booms, drumming or steady pulses rather than clear songs. Displaying flights and territorial calls of grouse and similar ground birds produce low-frequency thumps that carry across open ground. A slow, regular beat is a strong sign of an animal over distant traffic. 

Compare the rhythm and spacing of a low sound with the behavior you observe, because a steady hum can be a pump or a motor. Distant thunder rolls once and fades, while a drumming bird repeats on a steady interval. Note the direction with a second sensor if possible, so you can place the source on open ground. 

Some very low signals are heard rather than recorded clearly, and a faint boom near the bottom of the band may be only partly captured. Keep expectations modest about what an inexpensive sensor will reveal. A trained biologist can confirm a suspected call and should be asked before any record is published. 

## A field routine for infrasonic sessions 

A repeatable session routine makes low-frequency work easier to compare over the season. Arrive early, set the stand low, shield the sensor and log the conditions before pressing record. Leave the sensor still for a while, then start a fresh file for each watch period. 

Review the last files before you leave the site, so a loose cable or a broken shield can be fixed on the spot. In winter, keep batteries warm and expect cold to shorten runtime; in summer, keep the sensor out of direct sun. Repeat visits to the same spot build a library that shows what is truly new. 

Conditions to record include wind direction, cloud cover and the distance to noisy features such as roads or farm equipment. A gusty day can be left out of the dataset, since wind masks almost everything. Standing water and soft soil carry the stand unevenly and can tilt the mount, so check the level after each setup. 

## Skills, limits and safety in the field 

Infrasonic work needs field craft more than technical skill, and a few limits deserve a place in your notes. Wind is the honest ceiling on every session, and a gusty day produces files that hold little animal sound. No sensor removes wind noise; only placement and shielding help. 

Before any record leaves your notebook, a trained specialist should review the analysis, since interpreting low-frequency calls is a specialized job. Setting up on private land, steep ground or near livestock carries risks, and permission and safe footing matter more than a good spot. Keep distance from large animals and never enter water or unstable ground to place a sensor. 

Do not camp or walk near active machinery, and keep the sensor away from paths where people or animals could trip. In cold or wet weather, carry warm layers and a way to call for help. A quiet companion approach works better than a heroic one, so stop when wind or weather turns. 

## A season-by-season observing calendar 

Season shapes what you can record, and a simple calendar keeps the work focused. In spring, birds display on leks and open ground, which makes placement easier and wind more variable. Summer heat brings calm mornings and a louder insect layer but also more human noise. 

Autumn brings migrating flocks and steady winds, so pick low, sheltered spots and short sessions. Winter cold tightens battery life and hardens the ground, which changes how a stand holds. Deep snow muffles sound near the sensor but also hides the ground cover that softens the wind. 

Write down the season for each file, because a low boom in spring may be a display call while a similar sound in winter is a distant motor. A small notebook of dates and places lets you revisit a promising site next year. The calendar is the record that makes the recordings meaningful. 

## Questions About Infrasonic Animal Recording 

### What is an infrasonic sensor used for outdoors? 

An infrasonic sensor outdoors is used to detect and record sound below the range of human hearing, including low animal calls and environmental rumbles. It pairs with a recorder that stores those frequencies and with shielding that reduces wind noise. The sensor itself is a microphone built to respond to slow pressure changes. 

### Can I record animals with infrasound at home or in a quiet yard? 

Yes, a quiet yard can suit infrasonic recording if the sensor sits low and away from wind and traffic. A yard is sheltered, but nearby buildings, fans and roads add low-frequency noise. Record on calm mornings and compare files across several days before drawing conclusions. 

### How do I reduce wind noise at low frequencies? 

Wind noise at low frequencies shrinks when the sensor sits low, behind a porous shield, out of the direct air stream. Tape the cable to the stand and keep the lead slack so it cannot thump. A buried housing with a porous cover gives still air around the sensor at fixed sites. 

### Which low-frequency microphone suits a long field session? 

A low-frequency microphone with a sealed metal body, low noise floor and modest power draw suits a long field session. Check that its output suits your recorder, and test it on a calm day before an overnight watch. The best choice depends on how often you move the kit and how damp the site is. 

### Are animal infrasonic calls audible to people? 

No, true infrasonic animal calls sit below the pitch range people hear, so you rarely hear them directly. You may feel a low pulse or hear a lower boom where the call rises into audible sound. Software view and slowed playback are how most people inspect the signal. 

### Can I identify a species from a single infrasonic recording? 

Only rarely, because low-frequency calls carry little fine detail and wind masks many features. Recording rhythm, season and observed behavior give context that a single file lacks. A trained specialist should confirm identification before any record is published.
