# DIY Protective Gear for Field Equipment

Make your own protective gear for field equipment: a homemade cover, water repellent treatment and a protective case that keep binoculars and field bags dry.

DIY protective gear for field equipment means making your own covers, cases and water repellent treatments instead of buying ready-made ones. You build a covering that fits your optics and pack, then treat the fabric so rain and dust stay outside. The work suits cloth, foam and coated nylon, which are easy to cut and sew at home. 

- Measure the item with its strap or harness on before you cut any pattern.
- A homemade cover keeps rain off optics but blocks the lens, so choose a design you can open fast.
- Water repellent treatment is a finish you renew, not a one-time change to the fabric.
- A protective case needs padding at the corners, where a dropped field bag takes the hit.
- Test every cover and treatment outdoors before a long day on the prairie.
 

## What DIY protection needs to do 

DIY gear protection has one job: keep water, dust and knocks away from equipment you carry outdoors. A cover handles rain and grit, while padding handles impact from a drop or a swing against your hip. Decide which risk matters most for each item before you choose a material. 

Field equipment fails in three places, and a good design covers all of them. Water reaches seams and zippers first, dust works into lens threads and focus wheels, and impact lands on corners and edges. Plan the cover around those weak points rather than wrapping the whole item evenly. 

Access matters as much as protection. A birdwatching guide needs to raise binoculars in a moment, so a cover that must be untied or unzipped fully defeats its purpose. A flap, a drawcord or a single clip gives fast entry while still closing against weather. 

## Choosing cloth for a homemade cover 

A homemade cover works best in a tight-weave fabric that sheds water and stays quiet in the hand. Coated nylon and polyester ripstop resist rain without much weight, and they fold into a pocket when the sky clears. Cotton canvas is tougher but heavy and slow to dry once soaked. 

Quietness matters in the field, because loud fabric rustles when you lift your optics and can spook birds at close range. Soft-shell and brushed fabrics move silently and still resist a light shower. Check a fabric by rubbing it near your ear before you commit to it for a scope cover. 

Color affects heat and visibility, so pick a muted tone that blends with grass and brush. Dark fabric absorbs sun and grows hot on a scope tube, while pale fabric reflects light and shows dirt. A neutral olive or tan keeps the cover discreet and comfortable to touch. 

## Cutting a pattern that fits your gear 

A pattern starts with the item itself, measured with every strap, lens cap and harness attached. Lay the equipment on paper and trace its outline, then add enough room for the fabric to drape rather than stretch. Small errors here show up as a cover that will not close or a case that pinches. 

Add a seam allowance along every edge you plan to join, and mark the places where straps and openings will sit. A field bag protection cover needs openings for the shoulder strap and a clear route to the main zipper. Transfer these marks onto the cloth before cutting, because repositioning later wastes material. 

Make a first version in scrap cloth and fit it to the equipment before cutting the good fabric. A test piece reveals where the cover binds, where it hangs loose and where an opening sits in the wrong spot. Adjust the paper pattern from what the test shows, then cut the final fabric. 

## Sewing and sealing the seams 

Seams are the first place water enters a homemade cover, so they need closing beyond a simple stitch. Flat-felled seams fold the raw edges inside and leave a smooth surface that sheds rain. Where a flat seam is impractical, seal the stitched line with a strip of repair tape or a liquid seam sealer. 

Stitch with a needle and thread suited to the fabric weight, and keep the tension loose enough that the cloth does not pucker. A puckered seam pulls open under strain and lets water through. Test the stitch on a scrap piece and tug it before you sew the real cover. 

Finish every opening with a binding or a folded hem so the edge does not fray. Drawcords run through a hem channel and cinch the cover around a scope tube or a bag mouth. Bar tacks at stress points, such as strap anchors and clip tabs, stop the fabric from tearing. 

## Applying water repellent treatment 

Water repellent treatment makes fabric shed rain, but it does not make the material waterproof. A durable water repellent finish, often shortened to DWR, coats the fibers so droplets bead and roll off. The treatment wears away with use and abrasion, so it needs renewing on a schedule your own use sets. 

Apply a spray or wash-in treatment to clean, dry fabric and follow the product label for curing. A dirty cover holds treatment unevenly, so wash it first with a mild soap and rinse well. Work outdoors or in a ventilated space, because these products give off fumes. 

Test the treated cover by sprinkling water on it and watching whether the drops bead or soak in. Patches that darken and spread water need another coat. Reapply before a wet season rather than after the first soaking, when the fabric is already saturated. 

## Building padding into a protective case 

A protective case guards against impact, and closed-cell foam does that job without absorbing water. Foam sheets cut to fit the sides and base cushion the equipment inside the shell. Line the foam with a smooth fabric so it does not rub grit against lenses and coatings. 

Place the thickest padding at corners and the base, where a dropped field bag meets the ground. A thin layer along the sides adds little weight and stops the contents shifting against the shell. Leave the lid lightly padded so it closes without pressing on the optics. 

Choose a closure that stays shut in brush but opens without fuss. A buckle or a zipper with a pull tab suits a case that lives inside a pack, while a simple flap suits one carried on a belt. Check that no metal hardware touches the equipment when the case is closed. 

## Testing gear before a field day 

Test a new cover or case at home before you trust it on a long walk. Fill the cover with a cloth or the actual equipment, then spray it with water from a bottle for a few minutes. Look for damp patches at seams, zippers and openings and mark every one you find. 

Carry the finished gear on a short walk to check how it hangs and moves. A cover that swings or rubs becomes irritating over distance, and a strap that slips off the shoulder defeats field bag protection. Adjust the fit now rather than mid-route. 

Keep a small repair kit with the gear, holding a patch of the cover fabric, seam tape and a spare clip. Field repairs are part of homemade gear, and a quick patch restores protection until you can fix it properly at home. Note where failures happened so the next version avoids them. 

## Questions about DIY field gear protection 

### Can I make DIY protective gear without a sewing machine? 

Yes, DIY protective gear can be made by hand with a needle and thread, though seams take longer and need careful tension. Adhesive repair tape and fabric glue close some seams, but stitched seams hold better under strain. Padding can be cut and layered without any sewing at all. 

### Does water repellent treatment make a cover fully waterproof? 

No, water repellent treatment makes fabric shed rain but does not stop water under pressure or through seams. A treated homemade cover handles spray and light rain, not a soaking. Seal the seams and add a flap over openings if you expect heavy weather. 

### What fabric works for a homemade cover over binoculars? 

A quiet, tight-weave fabric such as coated nylon or soft-shell works well for a homemade cover over binoculars. The cloth should shed water, move silently and stay thin enough to fold away. Avoid stiff or noisy material that rustles when you lift the optics. 

### How do I protect a field bag that has no padding? 

You can add padding by cutting closed-cell foam sheets and lining the bag's base, sides and corners. Foam does not absorb water and cushions impact without much weight. Wrap the foam in smooth fabric so it does not rub grit against your equipment. 

### Can I treat a cover I already made? 

Yes, a cover you already made can be treated after it is washed and dried. Spray-on and wash-in products both work on most outdoor fabrics. Test a hidden patch first to confirm the treatment does not discolor the cloth.
